GSC Power-Division has released Stage 1 and Stage 2 cams for the 4B11T motor in the 2008-2010 Mitsubishi Evolution X and the 2010 Hyundai Genesis Coupe. Quantities available are limited so pre-order your set now through Touge Tuning.

Contact - Sales@tougetuning.com
Store - www.tougetuning.com/store

Retail Price: $699.00

Part Number: 6010S1

The GSC Power-Division S1 cams for the Mitsu Evolution X are designed for those with the stock turbo up to the 550hp range These cams will not sacrifice any bottom end loss over stock cams; nothing but gains and will promote faster spooling of the upgraded turbos. Gains of 20-50whp (depending on Turbo) have been seen by simply bolting the S1 cams in.
• Designed for a rev range of 3000-7500rpms
• the S1 cams work well on the stock valve springs
• Intake 264 / 220 @ .040" / Peak Lift 10.2mm
• Exhaust 264 / 216 @ .040" / Peak Lift 10.0mm

Part Number: 6010S2

The GSC Power-Division S2 cams for the Mitsu Evolution X are designed for those with 600HP+ in mind. Gains of 40-80whp (depending on Turbo) have been seen by simply bolting the S2 cams in.
• Designed for a rev range of 3800-8500rpms
• The S2 cams require an upgraded valve spring.
• Intake 274 / 230 @ .050" / Peak Lift 11.2mm
• Exhaust 274 / 230 @ .050" / Peak Lift 11.0mm

Retail Price: $699.00

Part Number: 6060S1

The GSC Power-Division S1 cams for the Hyundai Genesis Coupe 4B11T are designed for those with the stock turbo up to the 550hp range These cams will not sacrifice any bottom end loss over stock cams; nothing but gains and will promote faster spooling of the upgraded turbos. Gains of 20-50whp (depending on Turbo) have been seen by simply bolting the S1 cams in. Designed for a rev range of 3000-7500rpms, these cams work well on the stock valve springs.
• Designed for a rev range of 3000-7500rpms
• the S1 cams work well on the stock valve springs.
• Intake 264 / 220 @ .040" / Peak Lift 10.2mm
• Exhaust 264 / 216 @ .040" / Peak Lift 10.0mm

Part Number: 6060S2

The GSC Power-Division S2 cams for the Hyundai Genesis Coupe 4B11T are designed for those with 600HP+ in mind. Gains of 20-60whp (depending on Turbo).
• Designed for a rev range of 3500-8000rpms
• The S2 cams require an upgraded valve spring.
• Intake 272 / 226 @ .040" / Peak Lift 10.4mm
• Exhaust 270 / 222 @ .040" / Peak Lift 10.2mm

GSC Power Division has released JDM / Euro Spec STi Cams, technical information can be found below. For pricing and availability contact Sales@tougetuning.com

Application: Subaru EJ20 JDM/Euro Spec STi

Part Number 6027S1
S1 cams are good for the stock turbo to a 550hp turbo. 3000-7000rpm range. These cams require upgraded valve springs do to coil bind on the factory spring. (suggest spring kit 5025).

Intake 268 / 225 @ .040" / Peak Lift 10.8mm / Centerline AVCS
Exhaust 266 / 228 @ .040" / Peak Lift 10.2mm / Centerline 113

Part Number 6027S2
S2 cams are built to suite the higher horsepower Subys. With a power range of 500-750, you need some certain mods to utilize the full potential of the S2s such as a built motor and a ported head. 4000-8500 RPM Range. The S2 cams require upgraded valve springs do to coil bind on the factory spring. (spring kit 5025 is good to 28psi and 8k rpms; over 28psi or 8k rpms dual spring kit suggest)

Intake 272 / 226 @ .050" / Peak Lift 10.5mm / Centerline AVCS
Exhaust 272 / 232 @ .050" / Peak Lift 10.2mm / Centerline 113

Part Number 6027S3
The S3 cams are built to suite the highest horsepower drag Subys. With a power range of 750- 1000HP and a rev range of 4500-9500rpms, The S3 cams require abuilt motor, with a ported head (clearanced for cam lift), and a standalone engine management system. Dual valve springs are required.

Intake 282 / 240 @ .050" / Peak Lift 11.3mm / Centerline AVCS
Exhaust 282 / 240 @ .050" / Peak Lift 11.3mm / Centerline 113